RIDGID DP1500 Spécifications télécharger pdf (Page 3)

When Installing Or Moving The Drill Press

Reduce the Risk of Dangerous Environment.

• Use the drill press in a dry, indoor place protected from

rain.

• Keep work area well lighted.

• Use recommended accessories. The use of improper

accessories may cause risk of injury to persons.

To reduce the risk of injury from unexpected drill

press movement.

If there is any tendency of the drill press to tilt or

move during any use, bolt it to the floor. If the work-

piece is too large to easily support with one hand,

provide an auxiliary support.

• To reduce the risk of injury from electrical shock, make

sure your fingers do not touch the plug’s metal prongs

when plugging in or unplugging the drill press.

• Never Stand On Tool. Serious injury could occur if the

tool tips or you accidentally hit the cutting tool. Do not

store anything above or near the tool where anyone

might stand on the tool to reach them.

Before Each Use

Inspect your drill press.

• To reduce the risk of injury from accidental starting,

turn the switch off, unplug the drill press, and remove

the switch key before raising the guard, changing the

cutting tool, changing the setup, or adjusting anything.

Make sure switch is in OFF position before plugging in.

• Check for alignment of moving parts, binding of moving

parts, breakage of parts, drill press stability, and any

other conditions that may affect the way the drill press

works.

• If any part is missing, bent or broken in any way, or any

electrical part does not work properly, turn the drill

press off and unplug the drill press.

• Replace damaged or missing parts before using the

drill press again.

• Remove adjusting keys and wrenches. Form a habit of

checking for and removing keys and adjusting

wrenches from table top before turning drill press on.

• Make sure all clamps and locks are tight and no parts

have excessive play.

Use Only Accessories Designed For This Drill Press To Reduce The Risk of Serious Injury

From Thrown Broken Parts Or Work Pieces

• When cutting large diameter holes:

- Clamp the workpiece firmly to the table. Otherwise

the cutting may grab and spin it at high speed.

- Use only one piece, cup-type, hole cutters.

- Do not use fly cutters or multi-part hole cutters as

they can come apart or become unbalanced in use.

- Keep speed below 1500 R.P.M.

• Drum sanders must never be operated on this drill

press at a speed greater than 1800 R.P.M.

• Do not install or use any drill that exceeds 7” in length

or extends 6” below the chuck jaws. They can sud-

denly bend outward or break.

• Do not use wire wheels, router bits, shaper cutters, cir-

cle (fly) cutters or rotary planers on this drill press.

Kickback

• Kickback is the grabbing of the workpiece by the rotat-

ing tool. The workpiece can be thrown at very high

speed in the direction of rotation. This Can Cause

Serious Injury. To reduce the possibility of injury from

kickback:

• Clamp the workpiece firmly to the table whenever pos-

sible.

• Buffing or sanding wheels or drums should be con-

tacted on the side moving away from you, not the side

moving toward you.

• Use only recommended accessories and follow the

instructions supplied with the accessory.

This drill press has 12 speeds as listed below:

250 RPM 990 RPM

340 RPM 1550 RPM

390 RPM 1620 RPM

510 RPM 1900 RPM

600 RPM 2620 RPM

650 RPM 3100 RPM

See inside of guard for specific placement of belt on

pulleys.

Think Safety

Safety is a combination of operator common sense and

alertness at all times when the drill press is being used.

WARNING: Do not allow familiarity (gained from

frequent use of your drill press) to become com-

monplace. Always remember that a careless frac-

tion of a second is sufficient to inflict severe injury.

Plan Your Work

• Don’t force the tool. It will do the job better and safer at

the rate for which it was designed.

• Use the right tool. Don’t force tool or attachment to do

a job it was not designed to do.

• If any part of your drill press is missing, malfunctioning,

has been damaged or broken...such as the motor

switch, or other operating control, a safety device or

the power cord, turn the drill press off and unplug it

until the particular part is properly repaired or

replaced.

• Never place your fingers in a position where they could

contact the drill or other cutting tool if the workpiece

should unexpectedly shift or your hand should slip.

1 2 3 4 5 6 7 8 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

RIDGID DP1500 Spécifications Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques RIDGID DP1500